华硕网络产品技术交流平台

标题: TUF-AX3000，亮红灯一直显示联机中断，但能联网速度正常 [打印本页]

作者: deff_df 时间: 2020-2-17 21:41
标题: TUF-AX3000，亮红灯一直显示联机中断，但能联网速度正常
这两天来回刷不同的固件，改各种的设置，始终存在问题，现在刷完最新的8365固件后，2.4G和5G网速都正常了，但是一直显示联机中断，亮红灯，但能联网速度正常，虽然能用但总感觉不踏实，这是什么问题？

这个路由器太不稳定了，哎，

另外有没有什么彻底清除路由器存储的方法，比复位更彻底的方法，就好像安卓手机的双清，感觉复位初始化有时不完全

作者: Dr.Antenna 时间: 2020-2-17 22:25
断电后先按住wps, 再上电直到电源灯闪或是灭后再松开wps，等待开机重新设定应该是比较干净的了。若要升级或是更新固件记得更新后要勾选初始化

作者: deff_df 时间: 2020-2-17 22:51

Dr.Antenna 发表于 2020-2-17 22:25
断电后先按住wps, 再上电直到电源灯闪或是灭后再松开wps，等待开机重新设定应该是比较干净的了。若要升级或 ...

好的，谢谢

作者: 涵哥 时间: 2020-2-18 11:48
这种侦测亮红灯但是又能上网的环境，和你的运营商环境有关系的
在拿到WAN IP之后，路由器会定时的对WAN环境进行侦测，一般是DNS probe等，如果在某些多NAT环境中以及运营商设定过的环境中，路由可能会侦测失败，会提示你
但是呢，这又是运营商设定的，所以就造成能上网亮红灯的现象

总体不用担心，这个可能会侦测这种环境做修复

作者: deff_df 时间: 2020-2-18 17:08

涵哥发表于 2020-2-18 11:48
这种侦测亮红灯但是又能上网的环境，和你的运营商环境有关系的
在拿到WAN IP之后，路由器会定时的对WAN环境 ...

这样啊。好的

作者: popchild 时间: 2020-2-19 03:05
本帖最后由 popchild 于 2020-2-19 03:26 编辑

这问题偶也碰到过，路由器亮红灯但能上网，路由器后台显示联机中断。看到过大神的一篇帖子如下图设置参数后重启路由器红灯问题解决，感谢这位大神指教。目前使用7900版的固件，比较稳定，等官方有更稳定的版本再升级。
建议先恢复出厂设置，重启，更新固件，恢复出厂设置，重启，设置相关参数，提前把设置方案截图，不要用备份恢复，全部设置完毕，再重启一次，然后做个宽带测速即可。

[attach]13968[/attach]

作者: deff_df 时间: 2020-2-19 11:25

popchild 发表于 2020-2-19 03:05
这问题偶也碰到过，路由器亮红灯但能上网，路由器后台显示联机中断。看到过大神的一篇帖子如下图设置参数后 ...

谢谢，为什么不备份恢复，是备份恢复有时也会出现问题吗，我一直都是升级固件，初始化，然后恢复备份操作，我也觉得还是7900最稳定

作者: Master 时间: 2020-2-19 13:55

deff_df 发表于 2020-2-19 11:25
谢谢，为什么不备份恢复，是备份恢复有时也会出现问题吗，我一直都是升级固件，初始化，然后恢复备份操作 ...

备份旧固件的设定档，可能会将旧固件上的一些参数值一并保存下来，而这些参数值可能在新固件上同样会引起bug。

所以固件版本有变更的话，还是建议先初始化一次路由器，然后进行重新设定。

作者: popchild 时间: 2020-2-19 20:13

deff_df 发表于 2020-2-19 11:25
谢谢，为什么不备份恢复，是备份恢复有时也会出现问题吗，我一直都是升级固件，初始化，然后恢复备份操作 ...

不客气，8楼的大神已经回答你的问题了，看看红灯的问题是否解决？偶的已经OK了。

作者: deff_df 时间: 2020-2-19 22:29

popchild 发表于 2020-2-19 20:13
不客气，8楼的大神已经回答你的问题了，看看红灯的问题是否解决？偶的已经OK了。 ...

已解决

作者: popchild 时间: 2020-2-19 22:38

deff_df 发表于 2020-2-19 22:29
已解决

论坛还是有很多大神在的，希望能持续优化完善TUF-AX3000的固件，我这隔一堵墙或2墙，5G的信号比2.4G的信号好。不知道你的怎样？偶觉得好奇怪的说。

作者: popchild 时间: 2020-2-19 22:43

涵哥发表于 2020-2-18 11:48
这种侦测亮红灯但是又能上网的环境，和你的运营商环境有关系的
在拿到WAN IP之后，路由器会定时的对WAN环境 ...

@涵哥，@Dr.Antenna，@Master，谢谢大神持续优化TUF-AX3000的固件，红灯的问题，麻烦再看一下6楼的解决方案，希望在新版固件中能优化完善，谢谢~
还有个问题就是隔墙的2.4G的信号不如5G（已固定信道），希望能优化一下2.4G的信号，毕竟很多家用设备只支持2.4G。

作者: Master 时间: 2020-2-20 16:11

popchild 发表于 2020-2-19 22:43
@涵哥，@Dr.Antenna，@Master，谢谢大神持续优化TUF-AX3000的固件，红灯的问题，麻烦再看一下 ...

之后有机会，还是会持续推出优化TUF-AX3000的beta fw给坛友使用的，请关注！

作者: liang2200 时间: 2022-10-27 21:47
楼主，请问下我也遇见这个问题了无论怎么重置刷机都亮红灯，请问下到底如何解决啊

作者: Master 时间: 2022-10-28 09:23

liang2200 发表于 2022-10-27 21:47
楼主，请问下我也遇见这个问题了无论怎么重置刷机都亮红灯，请问下到底如何解决啊 ...

要看你的路由本身能不能出网，能出网，但亮红灯，算是bug。但这种误判原因也有很多种，最好点feedback到华硕官方，然后私信我们你留的邮箱，我们也可以同步请华硕工程师分析一下。

但本身就不能出网，亮红也算符合预期。

作者: youlv521 时间: 2023-8-14 16:03

Master 发表于 2022-10-28 09:23
要看你的路由本身能不能出网，能出网，但亮红灯，算是bug。但这种误判原因也有很多种，最好点feedback到 ...

我现在路由器也是这个问题，能出网，但是闪红灯，webUI里提示联机中断。

作者: 涵哥 时间: 2023-8-14 16:52

youlv521 发表于 2023-8-14 16:03
我现在路由器也是这个问题，能出网，但是闪红灯，webUI里提示联机中断。

原因就是我前面說的,如下

解決方案，推薦是固定WAN DNS為本市的公共DNS
-------------------------------

这种侦测亮红灯但是又能上网的环境，和你的运营商环境有关系的
在拿到WAN IP之后，路由器会定时的对WAN环境进行侦测，一般是DNS probe等，如果在某些多NAT环境中以及运营商设定过的环境中，路由可能会侦测失败，会提示你
但是呢，这又是运营商设定的，所以就造成能上网亮红灯的现象

总体不用担心，这个可能会侦测这种环境做修复
------------------------------

作者: youlv521 时间: 2023-8-14 17:05

涵哥发表于 2023-8-14 16:52
原因就是我前面說的,如下

解決方案，推薦是固定WAN DNS為本市的公共DNS

我试过固定DNS，虽然不是本市的。而且我也已经关闭了网络检测了

作者: 涵哥 时间: 2023-8-15 09:09

youlv521 发表于 2023-8-14 17:05
我试过固定DNS，虽然不是本市的。而且我也已经关闭了网络检测了

所以固定之後還是紅燈？

作者: youlv521 时间: 2023-8-15 09:27

涵哥发表于 2023-8-15 09:09
所以固定之後還是紅燈？

准确地讲应该是红白闪，但是webUI里面显示的联机中断

作者: 涵哥 时间: 2023-8-16 09:11

youlv521 发表于 2023-8-15 09:27
准确地讲应该是红白闪，但是webUI里面显示的联机中断

紅白閃？可以把log發出來看看

作者: youlv521 时间: 2023-8-17 07:23

涵哥发表于 2023-8-16 09:11
紅白閃？可以把log發出來看看

May  5 13:05:04 kernel: klogd started: BusyBox v1.24.1 (2022-04-28 10:52:47 CST)
May  5 13:05:04 kernel: Linux version 4.19.183 (defjovi@eva03) (gcc version 9.2.0 (Buildroot 2019.11.1)) #1 SMP PREEMPT Thu Apr 28 10:53:23 CST 2022
May  5 13:05:04 kernel: random: get_random_bytes called from start_kernel+0x9c/0x490 with crng_init=0
May  5 13:05:04 kernel: Kernel command line: console=ttyAMA0 earlyprintk debug irqaffinity=0 pci=pcie_bus_safe isolcpus=3 rootwait mtdparts=spi1.0:2097152(loader),264241152@2097152(image),524288@266338304(crashlog) root=/dev/ubiblock0_4 ubi.mtd=image ubi.block=0,4 rootfstype=squashfs cma=0M
May  5 13:05:04 kernel: Virtual kernel memory layout:
May  5 13:05:04 kernel:    vector  : 0xffff0000 - 0xffff1000 ( 4 kB)
May  5 13:05:04 kernel:    fixmap  : 0xffc00000 - 0xfff00000 (3072 kB)
May  5 13:05:04 kernel:    vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
May  5 13:05:04 kernel:    lowmem  : 0xc0000000 - 0xe0000000 ( 512 MB)
May  5 13:05:04 kernel:    pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
May  5 13:05:04 kernel:    modules : 0xbf000000 - 0xbfe00000 (  14 MB)
May  5 13:05:04 kernel:    .text : 0x(ptrval) - 0x(ptrval) (7136 kB)
May  5 13:05:04 kernel:    .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
May  5 13:05:04 kernel:    .data : 0x(ptrval) - 0x(ptrval) ( 248 kB)
May  5 13:05:04 kernel:       .bss : 0x(ptrval) - 0x(ptrval) ( 308 kB)
May  5 13:05:04 kernel: CCI hardware cache coherency enabled
May  5 13:05:04 kernel: bootloader version  U-Boot 2019.07 (Apr 28 2022 - 11:37:24 +0800), Build: 5.04L.0
May  5 13:05:04 kernel: inMemNvramData.szBoardId TUF_AX3000_V2
May  5 13:05:04 kernel: size of sk_buff 368
May  5 13:05:04 kernel: offset of cb in sk_buff 256
May  5 13:05:04 kernel: PMC driver initcall
May  5 13:05:04 kernel: PMC driver scanning DT
May  5 13:05:04 kernel: pmc match PMC brcm,bca-pmc-3-2
May  5 13:05:04 kernel:    Remapping PMC IO memories...
May  5 13:05:04 kernel:             phys             virt       size
May  5 13:05:04 kernel:    0x0000000080301018 0x00000000e0878018 0x00005080
May  5 13:05:04 kernel:    0x0000000080320000 0x00000000e0911000 0x00000240
May  5 13:05:04 kernel:    0x0000000080300400 0x00000000e0913400 0x000005d0
May  5 13:05:04 kernel:    0x0000000080380000 0x00000000e0915000 0x00001000
May  5 13:05:04 kernel: pmc_init

MC using DQM mode
May  5 13:05:04 kernel: map_hw_timer_interrupt,162: interrupt_id 22
May  5 13:05:04 kernel: map_hw_timer_interrupt,162: interrupt_id 23
May  5 13:05:04 kernel: map_hw_timer_interrupt,162: interrupt_id 24
May  5 13:05:04 kernel: map_hw_timer_interrupt,162: interrupt_id 25
May  5 13:05:04 kernel: Allocated EXT_TIMER number 3
May  5 13:05:04 kernel: Broadcom Timer Initialized
May  5 13:05:04 kernel: Broadcom GBPM v0.1 initialized
May  5 13:05:04 kernel: Broadcom IQoS v1.0 initialized
May  5 13:05:04 kernel: Broadcom Logger v0.1
May  5 13:05:04 kernel: /dev/bcmnet Char device registered
May  5 13:05:04 kernel: skb_free_task created successfully with start budget 256
May  5 13:05:04 kernel: ^[[0;34mBLOG v3.0 Initialized^[[0m
May  5 13:05:04 kernel: BLOG Rule v1.0 Initialized
May  5 13:05:04 kernel: Skip Legacy Led init
May  5 13:05:04 kernel: Initialise system trusted keyrings
May  5 13:05:04 kernel: Key type asymmetric registered
May  5 13:05:04 kernel: Asymmetric key parser 'x509' registered
May  5 13:05:04 kernel: bcm63xx-hsspi ff801000.spi: spi driver using polling mode
May  5 13:05:04 kernel: SPINAND ID
May  5 13:05:04 kernel: 0x2c
May  5 13:05:04 kernel: 0x24
May  5 13:05:04 kernel: 0x2c
May  5 13:05:04 kernel: 0x24
May  5 13:05:04 kernel: MICRON
May  5 13:05:04 kernel:  MT29F2G01AB
May  5 13:05:04 kernel: 3 cmdlinepart partitions found on MTD device spi1.0
May  5 13:05:04 kernel: Creating 3 MTD partitions on "spi1.0":
May  5 13:05:04 kernel: 0x000000000000-0x000000200000 : "loader"
May  5 13:05:04 kernel: 0x000000200000-0x00000fe00000 : "image"
May  5 13:05:04 kernel: 0x00000fe00000-0x00000fe80000 : "crashlog"
May  5 13:05:04 kernel: brcmboard registered
May  5 13:05:04 kernel: brcmboard: brcm_board_init entry
May  5 13:05:04 kernel: Last RESET due to SW reset
May  5 13:05:04 kernel: RESET reason: 0x80000000
May  5 13:05:04 kernel: DYING GASP IRQ Initialized and Enabled
May  5 13:05:04 kernel: bcm_i2c: Error in loading module
May  5 13:05:04 kernel: init procfs
May  5 13:05:04 kernel: Bridge Broadcom hooks registered
May  5 13:05:04 kernel: Registering SWP/SWPB emulation handler
May  5 13:05:04 kernel: Loading compiled-in X.509 certificates
May  5 13:05:04 kernel: ubi0: attaching mtd2
May  5 13:05:04 kernel: ubi0: scanning is finished
May  5 13:05:04 kernel: ubi0: attached mtd2 (name "image", size 252 MiB)
May  5 13:05:04 kernel: ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
May  5 13:05:04 kernel: ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
May  5 13:05:04 kernel: ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
May  5 13:05:04 kernel: ubi0: good PEBs: 2016, bad PEBs: 0, corrupted PEBs: 0
May  5 13:05:04 kernel: ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
May  5 13:05:04 kernel: ubi0: max/mean erase counter: 10/7, WL threshold: 4096, image sequence number: 315698409
May  5 13:05:04 kernel: ubi0: available PEBs: 386, total reserved PEBs: 1630, PEBs reserved for bad PEB handling: 40
May  5 13:05:04 kernel: ubi0: background thread "ubi_bgt0d" started, PID 87
May  5 13:05:04 kernel: Registered phy device: EGPHY:0x8
May  5 13:05:04 kernel: Registered phy device: GPY211:0x19
May  5 13:05:04 kernel: Registered phy device: 5GAE:0x6
May  5 13:05:04 kernel: Registered phy device: 5GAE:0x7
May  5 13:05:04 kernel: Registered phy device: MAC2MAC:0x1
May  5 13:05:04 kernel: Registered phy device: EGPHY:0x1
May  5 13:05:04 kernel: Registered phy device: EGPHY:0x2
May  5 13:05:04 kernel: Registered phy device: EGPHY:0x3
May  5 13:05:04 kernel: UBIFS (ubi0:10): background thread "ubifs_bgt0_10" started, PID 186
May  5 13:05:04 kernel: UBIFS (ubi0:10): UBIFS: mounted UBI device 0, volume 10, name "data"
May  5 13:05:04 kernel: UBIFS (ubi0:10): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
May  5 13:05:04 kernel: UBIFS (ubi0:10): FS size: 19808256 bytes (18 MiB, 156 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs)
May  5 13:05:04 kernel: UBIFS (ubi0:10): reserved for root: 935592 bytes (913 KiB)
May  5 13:05:04 kernel: UBIFS (ubi0:10): media format: w5/r0 (latest is w5/r0), UUID 0B65AD8D-B983-49A5-9702-EB042DAFF1ED, small LPT model
May  5 13:05:04 kernel: UBIFS (ubi0:11): background thread "ubifs_bgt0_11" started, PID 202
May  5 13:05:04 kernel: UBIFS (ubi0:11): UBIFS: mounted UBI device 0, volume 11, name "defaults"
May  5 13:05:04 kernel: UBIFS (ubi0:11): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
May  5 13:05:04 kernel: UBIFS (ubi0:11): FS size: 7237632 bytes (6 MiB, 57 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
May  5 13:05:04 kernel: UBIFS (ubi0:11): reserved for root: 341850 bytes (333 KiB)
May  5 13:05:04 kernel: UBIFS (ubi0:11): media format: w5/r0 (latest is w5/r0), UUID 8397B293-FF22-41D3-8790-30E3F2026E43, small LPT model
May  5 13:05:04 kernel: UBIFS (ubi0:13): background thread "ubifs_bgt0_13" started, PID 232
May  5 13:05:04 kernel: UBIFS (ubi0:13): UBIFS: mounted UBI device 0, volume 13, name "jffs2"
May  5 13:05:04 kernel: UBIFS (ubi0:13): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
May  5 13:05:04 kernel: UBIFS (ubi0:13): FS size: 51171328 bytes (48 MiB, 403 LEBs), journal size 2539520 bytes (2 MiB, 20 LEBs)
May  5 13:05:04 kernel: UBIFS (ubi0:13): reserved for root: 2416947 bytes (2360 KiB)
May  5 13:05:04 kernel: UBIFS (ubi0:13): media format: w5/r0 (latest is w5/r0), UUID 3CC6F234-CCCF-409B-8347-2A1D013236A2, small LPT model
May  5 13:05:04 kernel: wlcsm: module license 'Proprietary' taints kernel.
May  5 13:05:04 kernel: Disabling lock debugging due to kernel taint
May  5 13:05:04 kernel: BCMLIBS loaded...
May  5 13:05:04 kernel: Broadcom BPM Module Char Driver v0.1 Registered<304>^[[0m
May  5 13:05:04 kernel: Scratch pad is not initialized.
May  5 13:05:04 kernel: Scratch pad is not initialized.
May  5 13:05:04 kernel: Scratch pad is not initialized.
May  5 13:05:04 kernel: Scratch pad is not initialized.
May  5 13:05:04 kernel: Scratch pad is not initialized.
May  5 13:05:04 kernel: Scratch pad is not initialized.
May  5 13:05:04 kernel: ^[[0;34m[NTC bpm] bpm_init_buf_pool: buf_top_idx:3447^[[0m
May  5 13:05:04 kernel: ^[[0;34m[NTC bpm] bpm_init_skb_pool: skbs pool inited total 3447^[[0m
May  5 13:05:04 kernel: License chip name: 6756 serial number: 000000000000000000000000
May  5 13:05:04 kernel: brcmchipinfo: brcm_chipinfo_init entry
May  5 13:05:04 kernel: Broadcom Ingress QoS Module  Char Driver v1.0 Registered<303>^[[0m
May  5 13:05:04 kernel: Broadcom Ingress QoS v1.0 initialized
May  5 13:05:04 kernel: ^[[0;36;44mBroadcom Packet Flow Cache ^[[0m
May  5 13:05:04 kernel: FCACHE_CONFIG_MAX_UCAST_FLOW_ENTRIES<16384>
May  5 13:05:04 kernel: FCACHE_CONFIG_MAX_MCAST_GROUPS<128>
May  5 13:05:04 kernel: FCACHE_CONFIG_MAX_MCAST_CLIENTS_PER_GROUP<63>
May  5 13:05:04 kernel: FCACHE_CONFIG_MAX_MCAST_CLIENTS<1024>
May  5 13:05:04 kernel: FCACHE_CONFIG_MAX_FDB_ENTRIES<1024>
May  5 13:05:04 kernel: FCACHE_CONFIG_MAX_HOST_DEV_ENTRIES<64>
May  5 13:05:04 kernel: FCACHE_CONFIG_MAX_HOST_MAC_ENTRIES<32>
May  5 13:05:04 kernel: npe_max_entries<35072>
May  5 13:05:04 kernel: Bind blog_notify_evt_enqueue_fn[<bf0e28bc>]
May  5 13:05:04 kernel: fc_evt task created successfully
May  5 13:05:04 kernel: max_ent = 17536 intvl_msec = 10000 num_slices = 2000 num_ent = 9 period_msec = 5
May  5 13:05:04 kernel: NBUFF v1.0 Initialized
May  5 13:05:04 kernel: fcache: mcast_max_groups<128> mcast_max_clients_per_group<63> mcast_max_clients<1024>
May  5 13:05:04 kernel: fcache: mcast_max_ent<1152>
May  5 13:05:04 kernel: fcache: ucast_max_ent<16384>
May  5 13:05:04 kernel: fcache: max_ent<17536>
May  5 13:05:04 kernel: ^[[0;36;44mTotal # of labels = 77^[[0m
May  5 13:05:04 kernel: ^[[0;36;44mInitialized fcache state^[[0m
May  5 13:05:04 kernel: Pkt HW acceleration is disabled/unavailable.
May  5 13:05:04 kernel: ^[[0;36;44mBroadcom Packet Flow Cache  Char Driver v4.0 Registered<302>^[[0m
May  5 13:05:04 kernel: fc_timer_task created successfully
May  5 13:05:04 kernel: Pkt HW acceleration is disabled/unavailable.
May  5 13:05:04 kernel: Created Proc FS /procfs/fcache
May  5 13:05:04 kernel: ^[[0;36;44mBroadcom Packet Flow Cache registered with netdev chain^[[0m
May  5 13:05:04 kernel: ^[[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.^[[0m
May  5 13:05:04 kernel: ^[[0;35m[FHW]  pktDbgLvl[0x43428d25]=0^[[0m
May  5 13:05:04 kernel: ^[[0;34m[FHW]  fhw_construct: ^[[0m
May  5 13:05:04 kernel: ^[[0;36;44mInitialized Fcache HW accelerator layer state^[[0m
May  5 13:05:04 kernel: flwStatsThread created. numFlwsPerPoll 584 maxFlwIdx 17535
May  5 13:05:04 kernel: ^[[0;36;44mFcache Pathstats created^[[0m
May  5 13:05:04 kernel: ^[[0;36;44mConstructed Broadcom Packet Flow Cache v4.0^[[0m
May  5 13:05:04 kernel: Broadcom Command List Driver v1.0
May  5 13:05:04 kernel: ^[[0;36;44mBroadcom Archer Packet Accelerator Intializing^[[0m
May  5 13:05:04 kernel: Open archer Netdevice
May  5 13:05:04 kernel: Archer DS DPI Initialized
May  5 13:05:04 kernel: Archer US DPI Initialized
May  5 13:05:04 kernel: Archer WLAN Interface Construct (Threshold 32 packets, Timeout 500 usec, Jiffies 10)
May  5 13:05:04 kernel: Archer WLAN Rx Thread Initialized
May  5 13:05:04 kernel: Sysport 0 WOL IRQ 55
May  5 13:05:04 kernel: Sysport Driver User IRQ: 0x80498284
May  5 13:05:04 kernel: SYSPORT Driver Constructed (Budget: 128, Coalescing: 826828 nsec)
May  5 13:05:04 kernel: SYSPORT User IRQ: interrupt_id 54, controller 4 (phys 0x80498284)
May  5 13:05:04 kernel: Archer DHD Initialized
May  5 13:05:04 kernel: Archer Mode set to L2+L3
May  5 13:05:04 kernel: Archer Mode set to L2+L3
May  5 13:05:04 kernel: Initialized Archer Host Layer
May  5 13:05:04 kernel: Flow Table (160, 40): 6847d52a, 2621440 bytes
May  5 13:05:04 kernel: Flow Info Table (44, 65536): 366d5804, 2883584 bytes
May  5 13:05:04 kernel: Command List Table (128): virt 0xb7445c3a, phys 0x38a92347, size 2244608 bytes
May  5 13:05:04 kernel: Command List Control Table (8): 501fd666, 140288 bytes
May  5 13:05:04 kernel: Sysport Classifier: Max Flows = 17536 / 65536
May  5 13:05:04 kernel: Archer IQ status changed from 0 to 1
May  5 13:05:04 kernel: ^[[0;34m[NTC bitpool] idx_pool_init: 551:FHW[0]:Create Index Pool_Size = 17536^[[0m
May  5 13:05:04 kernel: Retrieve num_fhw_path=64
May  5 13:05:04 kernel: ^[[0;36;44mPathstats allocated 2048 bytes^[[0m
May  5 13:05:04 kernel: ^[[0;36;44mBroadcom Packet Flow Cache HW acceleration enabled.^[[0m
May  5 13:05:04 kernel: Enabled Archer binding to Flow Cache
May  5 13:05:04 kernel: ^[[0;36;44mBroadcom Archer Network Processor Char Driver v0.1 Registered <339>^[[0m
May  5 13:05:04 kernel: Archer TCP Pure ACK Enabled
May  5 13:05:04 kernel: bcmenet DT
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x0
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x1
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 56 to 0x00006000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 57 to 0x00006000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 58 to 0x00006000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 59 to 0x00006000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 60 to 0x00006000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 61 to 0x00006000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 62 to 0x00016000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 63 to 0x00016000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 64 to 0x00016000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 65 to 0x00016000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 66 to 0x00016000
May  5 13:05:04 kernel: set RGMII pad ctrl for GPIO 67 to 0x00016000
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x1
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x2
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x3
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x8
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x5
May  5 13:05:04 kernel: Registered mac device: SF2MAC:0x8
May  5 13:05:04 kernel: Lift external switch (sw1) out of Reset
May  5 13:05:04 kernel: LAG/Trunking enabled <0x08>
May  5 13:05:04 kernel: ephy_leds_init SW 0 Port 0 led idx 0 configured as:
May  5 13:05:04 kernel: led ctrl 0x00000003 encode 0x0003fb7f encode sel 0x00000480
May  5 13:05:04 kernel: ^[[0;30;102m=== Start of 5G Active Ethernet Initialization for core 0, lane 0 ===^[[0m
May  5 13:05:04 kernel: --- Step 0 powerup/reset sequence of core #0 at address 6
May  5 13:05:04 kernel: INFO _merlin28_core_power_op(): START powering up Merlin Core #0 with PRTAD = 6, ln_offset_stap = 0
May  5 13:05:04 kernel: INFO _merlin28_core_power_op(): Disable IDDQ
May  5 13:05:04 kernel: INFO _merlin28_core_power_op(): Provide a delay of 1ms after IDDQ is de-asserted
May  5 13:05:04 kernel: INFO _merlin28_core_power_op(): Disable serdes_reset and refclk_reset
May  5 13:05:04 kernel: MerlinSupport::merlin28_powerdn_lane(): powering down core #0x0 lane #0x0
May  5 13:05:04 kernel: MerlinSupport::merlin28_powerdn_lane(): powering down core #0x0 lane #0x1
May  5 13:05:04 kernel: MerlinSupport::merlin28_powerup_lane(): powering up core #0x0 lane #0x0
May  5 13:05:04 kernel: Toggle Serdes Core #0 LANE #0 PMD and uC reset.
May  5 13:05:04 kernel: INFO merlin28_core_init(): END. Core #0 with PRTAD = 6, ln_offset_stap = 0
May  5 13:05:04 kernel: merlin28_serdes_init(): Step 4.a Set uc_active = 1
May  5 13:05:04 kernel: merlin28_serdes_init(): Step 4. Assert micro reset
May  5 13:05:04 kernel: merlin28_serdes_init(): Step 4.a.2 Micro code load and verify
May  5 13:05:04 kernel: merlin28_load_firmware(): INFO: Start to download firmware to core # 0
May  5 13:05:04 kernel: merlin28_load_firmware():  Checking init_done initial value passed...
May  5 13:05:04 kernel: merlin28_load_firmware():  Checking init_done passed ...
May  5 13:05:04 kernel: merlin28_load_firmware():  begin writing firmware to the program ram ...
May  5 13:05:04 kernel: #################################################################################
May  5 13:05:04 kernel: merlin28_load_firmware():  end writing firmware to the program ram ...
May  5 13:05:04 kernel: Micro code read back verification succeeded
May  5 13:05:04 kernel: merlin28_serdes_init(): Step 4.b De-assert micro reset
May  5 13:05:04 kernel: merlin28_serdes_init(): Step 4.c wait for uc_dsc_ready_for_cmd = 1
May  5 13:05:04 kernel: merlin28_mptwo_poll_uc_dsc_ready_for_cmd_equals_1():  micro is ready for command ...
May  5 13:05:04 kernel: INFO merlin28_serdes_init(): END Merlin Initialization procedure
May  5 13:05:04 kernel: MerlinSupport::merlin28_powerup_lane(): powering up core #0x0 lane #0x0
May  5 13:05:04 kernel: merlin28_lane_init(): Step 4.c wait for uc_dsc_ready_for_cmd = 1
May  5 13:05:04 kernel: merlin28_speed_set_core(): Step 7 Config Speed to 2
May  5 13:05:04 kernel: merlin28_speed_set_core(): Step 8. PLL Configuration
May  5 13:05:04 kernel: merlin28_speed_set_core(): Initialize 9.375G VCO programming
May  5 13:05:04 kernel: No option found for: "-d ML_REFCLK_156P25", added default value 0 in index 9
May  5 13:05:04 kernel: merlin28_speed_set_core(): PMD Setup 50MHz, 9.375GHz VCO programming
May  5 13:05:04 kernel: merlin28_speed_set_core(): Step 9. Configure Core level regsiter
May  5 13:05:04 kernel: merlin28_speed_set_core(): Step 10. Set core_congif_from_pcs
May  5 13:05:04 kernel: merlin28_speed_set_core(): RAM variable vco_rate is 15
May  5 13:05:04 kernel: merlin28_cfg_core_ram_var(): program core_config_word 0x1e to ram address 0x50 ...
May  5 13:05:04 kernel: merlin28_speed_set_core(): Step 9. Reset Datapath (core)
May  5 13:05:04 kernel: merline28_datapath_get_core_out_reset(): Datapath Reset (core) in progress
May  5 13:05:04 kernel: merlin28_check_pll_lock(): Checking Core #0 PLL Lock Status
May  5 13:05:04 kernel: merlin28_check_pll_lock(): PLL Locked
May  5 13:05:04 kernel: merlin28_lane_config_speed(): Step 10. Lane Configuration
May  5 13:05:04 kernel: merlin28_lane_config_speed(): Step 13.a. Configure lane registers
May  5 13:05:04 kernel: merlin28_lane_config_speed(): Step 13.b. Configure lane's micro RAM vaiables
May  5 13:05:04 kernel: merlin28_lane_config_speed(): RAM variable an_enabled is 0
May  5 13:05:04 kernel: merlin28_cfg_lane_ram_var():  program lane_config_word 0x4 to ram address 0x400 ...
May  5 13:05:04 kernel: merlin28_lane_config_speed(#2):
May  5 13:05:04 kernel: CONFIGURING FOR FORCE 1G
May  5 13:05:04 kernel: INFO merlin28_lane_config_speed(): END Merlin core #0 lane #0 Initialization procedure
May  5 13:05:04 kernel: INFO merlin28_speed_set_core(): END Merlin Initialization procedure
May  5 13:05:04 kernel: ^[[0;30;102m=== End of 5G Active Ethernet Initialization for core 0, lane 0 ===^[[0m
May  5 13:05:04 kernel: [dsl_runner_gpy211_phy_init(325)] phy addr=0x19, phyid=0x67c9de10
May  5 13:05:04 kernel: [dsl_cl45phy_set_speed(420)] name=GPY211, speed=0, duplex=2, config_speed=-1
May  5 13:05:04 kernel: [GPY211_SET_SPEED(381)] auto-nego mode
May  5 13:05:04 kernel: LAG/Trunking enabled <0x08>
May  5 13:05:04 kernel: SYSPORT Host Binding Successfull
May  5 13:05:04 kernel: Archer CPU Affinity = 3
May  5 13:05:04 kernel: eth1    : Down       00:90:4C:32:A4

0 IntSw

0 Lgcl: 0 LAN PHY_ID:0x08:OnChip NoApd PwrDn 1 Gbps EGPHY Cfg: ANG. 1 Gbps; Down Unknown
May 5 13:05:04 kernel: <IntnlDev>: Up 1 Gbps 00:00:00:00:00:00 IntSw

1 Lgcl: 1 PHY_ID:0x01:OnChip RGMII NoApd PwrUp Unknown 2_EXTSW Cfg: FIX. 1 Gbps; Down Unknown
May 5 13:05:04 kernel: eth0 : Down 00:90:4C:32:A4

0 IntSw

5 Lgcl: 5 LAN    S1K2K
May  5 13:05:04 kernel:          PHY_ID:0x06:OnChip    ApdOn PwrDn    5 Gbps 5GAE#L0.0 Cfg: ANG.  5 Gbps;          Down                               S1K2K5R:             S1K2K:          SGMII
May  5 13:05:04 kernel:          PHY_ID:0x19:Extrnl Cscde NoApd PwrDn    2.5 Gbps    GPY211 Cfg: ANG.2.5 Gbps;          Dow
May  5 13:05:04 kernel: n                               S1K2K:             S1K2K:       Uknown
May  5 13:05:04 kernel: <IntnlDev>: Up 1 Gbps 00:00:00:00:00:00 IntSw

8 Lgcl: 8
May 5 13:05:04 kernel: eth2 : Down 00:90:4C:32:A4

0 ExtSw

1 Lgcl: 9 LAN PHY_ID:0x01:OnChip NoApd PwrDn 1 Gbps EGPHY Cfg: ANG. 1 Gbps; Down Unknown
May 5 13:05:04 kernel: eth3 : Down 00:90:4C:32:A4

0 ExtSw

2 Lgcl:10 LAN PHY_ID:0x02:OnChip NoApd PwrDn 1 Gbps EGPHY Cfg: ANG. 1 Gbps; Down Unknown
May 5 13:05:04 kernel: eth4 : Down 00:90:4C:32:A4

0 ExtSw

3 Lgcl:11 LAN PHY_ID:0x03:OnChip NoApd PwrDn 1 Gbps EGPHY Cfg: ANG. 1 Gbps; Down Unknown
May 5 13:05:04 kernel: <IntnlDev>: Up 1 Gbps 00:00:00:00:00:00 ExtSw

8 Lgcl:16
May  5 13:05:04 kernel: logical_port 0: intf_index 0, switch_index 0, phys_port 0 -> port_index 0, nbr_of_queues 8
May  5 13:05:04 kernel: logical_port 1: intf_index 0, switch_index 0, phys_port 5 -> port_index 1, nbr_of_queues 4
May  5 13:05:04 kernel: logical_port 2: intf_index 0, switch_index 1, phys_port 1 -> port_index 2, nbr_of_queues 4
May  5 13:05:04 kernel: logical_port 3: intf_index 0, switch_index 1, phys_port 2 -> port_index 3, nbr_of_queues 4
May  5 13:05:04 kernel: logical_port 4: intf_index 0, switch_index 1, phys_port 3 -> port_index 4, nbr_of_queues 4
May  5 13:05:04 kernel: SYSPORT[0]: port[0] -> nbr_of_brcm_tags 1
May  5 13:05:04 kernel: SYSPORT[0]: port[1] -> nbr_of_brcm_tags 1
May  5 13:05:04 kernel: SYSPORT[0]: port[2] -> nbr_of_brcm_tags 2
May  5 13:05:04 kernel: SYSPORT[0]: port[3] -> nbr_of_brcm_tags 2
May  5 13:05:04 kernel: SYSPORT[0]: port[4] -> nbr_of_brcm_tags 2
May  5 13:05:04 kernel: SYSPORT[0] = SWITCH_STACKED
May  5 13:05:04 kernel: RXQ[0]: IRQ 50, CPU 3
May  5 13:05:04 kernel: CSB Initialized: 0xdb2d7000 (0xdb2d7000), size 64 (128)
May  5 13:05:04 kernel: Ports 5, TDMA Rings 24
May  5 13:05:04 kernel: BCM6756_A1: ipg_length = 12 (0xe0882400 = 0x1)
May  5 13:05:04 kernel: Archer DMA Layer Initialized
May  5 13:05:04 kernel: Sysport Recycle Task: IRQ 51, CPU 3
May  5 13:05:04 kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
May  5 13:05:04 kernel: bcm_enet_init_post

2395 ENET system contructed and configured enet-kthrd thread
May 5 13:05:04 kernel: enet_kthread_handler

297 Instantiating ENET thread
May  5 13:05:04 kernel: bcm_mcast_init successful
May  5 13:05:04 kernel: Broadcom PCIe Host Controller Driver (impl1)^M
May  5 13:05:04 kernel: bcm-pcie: DEF CFG: ssc 0x0, speed  0x0, bootorder 0x0, apon 0x0
May  5 13:05:04 kernel: bcm-pcie:       : pwr 0x0, errlog 0x1111, msi 0x1111, acc  0x1111, pllclkid 0x3210
May  5 13:05:04 kernel: bcm-pcie:       : loglevel 0x1 pllclkadj 0x0
May  5 13:05:04 kernel: bcm-pcie: [1] DT node available: pcie@85000000
May  5 13:05:04 kernel: bcm-pcie: found Port [1] GEN0 Core Rev [1.00] with 0 Lanes^M
May  5 13:05:04 kernel: bcm-pcie: [1] vcore [0] initialized with [2] devices^M
May  5 13:05:04 kernel: bcm-pcie: Core [0] DT node available: pcie0
May  5 13:05:04 kernel: bcm-pcie: found Port [0] GEN2 Core Rev [4.02] with 2 Lanes^M
May  5 13:05:04 kernel: getrcal for res select 5, int 657, ext 637, ratio 124 ratio1 144, rcal 9
May  5 13:05:04 kernel: bcm-pcie: Core [0] setting resistor calibration value to 0x9
May  5 13:05:04 kernel: bcm-pcie: Core [0] link is DOWN^M
May  5 13:05:04 kernel: bcm-pcie: Core [0] dev [0] powered down^M
May  5 13:05:04 kernel: broadcomThermalDrv brcm-therm: init (CPU count 4 4 4 4)
May  5 13:05:04 kernel: brcm_otp_init entry
May  5 13:05:04 kernel: emf: Unknown symbol osl_malloc (err -2)
May  5 13:05:04 kernel: emf: Unknown symbol osl_pktdup_cpy (err -2)
May  5 13:05:04 kernel: emf: Unknown symbol osl_mfree (err -2)
May  5 13:05:04 kernel: emf: Unknown symbol linux_pktfree (err -2)
May  5 13:05:04 kernel: emf: Unknown symbol osl_pktdup (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_wmf_scbfind (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol osl_malloc (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_mfdb_ipv6_membership_add (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol osl_detach (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_rtport_del (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_igmp_snooper_register (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol osl_attach (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_mfdb_ipv6_membership_del (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_wmf_get_igsc (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_rtport_add (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_igmp_snooper_unregister (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_mfdb_membership_del (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol osl_mfree (err -2)
May  5 13:05:04 kernel: igs: Unknown symbol emfc_mfdb_membership_add (err -2)
May  5 13:05:04 kernel: Archer TCP Pure ACK Enabled
May  5 13:05:04 kernel: Loading wlshared Module...
May  5 13:05:04 kernel: cfg80211: Loading compiled-in X.509 certificates for regulatory database
May  5 13:05:04 kernel: cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
May  5 13:05:04 kernel: platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
May  5 13:05:04 kernel: Loading HND Module
May  5 13:05:04 kernel: igs_module_init:840:    IGS 29 create network socket successful
May  5 13:05:04 kernel: osl_skb_audit: PASS
May  5 13:05:04 kernel: wl_module_init: passivemode set to 0x1
May  5 13:05:04 kernel: wl_module_init: txworkq set to 0x0
May  5 13:05:04 kernel: ^[[0;32mwl_pktfwd_sys_init:  ^[[1m^[[34mWL_PKTFWD[1.1.0]^[[0m Success^[[0m
May  5 13:05:04 kernel: si_doattach: using BAR0 value: enum_base=85000000
May  5 13:05:04 kernel: BME Service Initialization
May  5 13:05:04 kernel: BME: M2M Core id 0x844 rev 132
May  5 13:05:04 kernel: M2M Service Initialization: M2M_DD_ENAB 0x00000003
May  5 13:05:04 kernel: M2M: M2M Core id 0x844 rev 132
May  5 13:05:04 kernel: M2M: SUCCESS eng 0 alloc rings <ba2995c9,1c22c79e>,90e7111c depth 256
May  5 13:05:04 kernel: M2M: SUCCESS eng 1 alloc rings <858d5231,fd3def1f>,4289f42e depth 256
May  5 13:05:04 kernel: M2M: DMA 0 IntRcvLazy 01000000
May  5 13:05:04 kernel: M2M: DMA 0 RcvCtrl XmtCtrl enabled
May  5 13:05:04 kernel: M2M: DMA 1 IntRcvLazy 01000000
May  5 13:05:04 kernel: M2M: DMA 1 RcvCtrl XmtCtrl enabled
May  5 13:05:04 kernel: wl0: wlc_ap_attach dynamic_ed_thresh_enable = 0
May  5 13:05:04 kernel: BME:register key<1010804> user RLM sel IDX set 1 mem 4 8 hi 0 0
May  5 13:05:04 kernel: CSIMON module registered
May  5 13:05:04 kernel: wl0_awl attach successful tx: 1, rx: 2
May  5 13:05:04 kernel: WL_FLCTL[0] bpm_total_skb 17236, exhaustion_hi 1723, exhaustion_lo 4309, prio_favor 4
May  5 13:05:04 kernel: ^[[0;34mArcher WLAN Bind: eth%d, wl_radio_idx 0, radio_index 0, mode SKB^[[0m
May  5 13:05:04 kernel: Archer WLAN XFER Thread 0 Initialized
May  5 13:05:04 kernel: ^[[0;32mwl_wfd_bind: wl0 wfd_idx 0 success^[[0m
May  5 13:05:04 kernel: eth5: Broadcom BCM6756 802.11 Wireless Controller 17.10.188.6401 (r808804)
May  5 13:05:04 kernel: dgasp: kerSysRegisterDyingGaspHandler: eth5 registered
May  5 13:05:04 kernel: si_doattach: using BAR0 value: enum_base=86000000
May  5 13:05:04 kernel: BME Service Initialization
May  5 13:05:04 kernel: BME: M2M Core id 0x844 rev 132
May  5 13:05:04 kernel: M2M Service Initialization: M2M_DD_ENAB 0x00000003
May  5 13:05:04 kernel: M2M: M2M Core id 0x844 rev 132
May  5 13:05:04 kernel: M2M: SUCCESS eng 0 alloc rings <ebc98e68,3eb38b23>,4b4f6312 depth 256
May  5 13:05:04 kernel: M2M: SUCCESS eng 1 alloc rings <f17dcfdd,cdefec4c>,4c011110 depth 256
May  5 13:05:04 kernel: M2M: DMA 0 IntRcvLazy 01000000
May  5 13:05:04 kernel: M2M: DMA 0 RcvCtrl XmtCtrl enabled
May  5 13:05:04 kernel: M2M: DMA 1 IntRcvLazy 01000000
May  5 13:05:04 kernel: M2M: DMA 1 RcvCtrl XmtCtrl enabled
May  5 13:05:04 kernel: wl1: wlc_ap_attach dynamic_ed_thresh_enable = 0
May  5 13:05:04 kernel: BME:register key<1010804> user RLM sel IDX set 1 mem 4 8 hi 0 0
May  5 13:05:04 kernel: CSIMON module registered
May  5 13:05:04 kernel: wl1_awl attach successful tx: 1, rx: 2
May  5 13:05:04 kernel: WL_FLCTL[1] bpm_total_skb 17236, exhaustion_hi 1723, exhaustion_lo 4309, prio_favor 4
May  5 13:05:04 kernel: ^[[0;34mArcher WLAN Bind: eth%d, wl_radio_idx 1, radio_index 1, mode SKB^[[0m
May  5 13:05:04 kernel: Archer WLAN XFER Thread 1 Initialized
May  5 13:05:04 kernel: ^[[0;32mwl_wfd_bind: wl1 wfd_idx 1 success^[[0m
May  5 13:05:04 kernel: eth6: Broadcom BCM6756 802.11 Wireless Controller 17.10.188.6401 (r808804)
May  5 13:05:04 kernel: dgasp: kerSysRegisterDyingGaspHandler: eth6 registered
May  5 13:05:04 kernel: eth0 (Int switch port: 5) (Logical Port: 5) (phyId: 19) Link Up at 1000 mbps full duplex
May  5 13:05:04 kernel: bcm_bca_usb_ctrl_probe: usb3_enable 1 xhci_enable 1
May  5 13:05:04 kernel: hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
May  5 13:05:08 kernel: CSIMON:  CSIMON[1.1.0] Initialization
May  5 13:05:08 kernel: Wowl not supported (-23)
May  5 13:05:08 kernel: CSIMON:  CSIMON[1.1.0] Initialization
May  5 13:05:08 kernel: CSIMON: M2M usr already registered ...
May  5 13:05:08 kernel: CSIMON:  CSIMON[1.1.0] Initialization
May  5 13:05:08 kernel: Wowl not supported (-23)
May  5 13:05:08 kernel: CSIMON:  CSIMON[1.1.0] Initialization
May  5 13:05:08 kernel: CSIMON: M2M usr already registered ...
May  5 13:05:09 kernel: eth1 (Int switch port: 0) (Logical Port: 0) (phyId: 8) Link Up at 1000 mbps full duplex
May  5 13:05:10 kernel: eth2 (Ext switch port: 1) (Logical Port: 9) (phyId: 1) Link Up at 1000 mbps full duplex
May  5 13:05:10 kernel: CSIMON:  CSIMON[1.1.0] Initialization
May  5 13:05:10 kernel: CSIMON: M2M usr already registered ...
May  5 13:05:10 kernel: In wl_dfs_cac_notify_status chanspec 0x1001 DFS state 0
May  5 13:05:10 kernel: CSIMON:  CSIMON[1.1.0] Initialization
May  5 13:05:10 kernel: CSIMON: M2M usr already registered ...
May  5 13:05:10 kernel: In wl_dfs_cac_notify_status chanspec 0xec32 DFS state 0
May  5 13:05:10 acsd: eth5: Selecting 2g band ACS policy
May  5 13:05:11 avahi-daemon[2028]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns!
May  5 13:05:12 avahi-daemon[2028]: Alias name "TUF-AX3000_V2" successfully established.
May  5 13:05:12 kernel: eth0 (Int switch port: 5) (Logical Port: 5) (phyId: 19) Link DOWN.
May  5 13:05:13 kernel: eth4 (Ext switch port: 3) (Logical Port: 11) (phyId: 3) Link Up at 1000 mbps full duplex
May  5 13:05:15 acsd: eth5: selected channel spec: 0x100a (10)
May  5 13:05:15 acsd: eth5: Adjusted channel spec: 0x100a (10)
May  5 13:05:15 acsd: eth5: selected channel spec: 0x100a (10)
May  5 13:05:15 acsd: eth6: Selecting 5g band ACS policy
May  5 13:05:19 GPY211: GPY211 speed war!
May  5 13:05:19 TUF-AX3000_V2: start httpd:80
May  5 13:05:19 httpd: Save SSL certificate...80
May  5 13:05:19 disk monitor: be idle
May  5 13:05:19 hour monitor: daemon is starting
May  5 13:05:19 hour monitor: daemon terminates
May  5 13:05:19 httpd: mssl_cert_key_match : PASS
May  5 13:05:19 miniupnpd: it is advised to use network interface name instead of 192.168.50.1/255.255.255.0
May  5 13:05:19 ERP: The model isn't under EU SKU!
May  5 13:05:19 miniupnpd[2104]: Cannot get IP address for ext interface . Network is down
May  5 13:05:19 miniupnpd[2104]: HTTP listening on port 38163
May  5 13:05:19 miniupnpd[2104]: Listening for NAT-PMP/PCP traffic on port 5351
May  5 13:05:19 httpd: Succeed to init SSL certificate...80
May  5 13:05:21 cfg_server:  event: wl_chanspec_changed_action
May  5 13:05:21 cfg_server: skip event due no re
May  5 13:05:22 pppd[2176]: pppd 2.4.7 started by admin, uid 0
May  5 13:05:22 kernel: SCSI subsystem initialized
May  5 13:05:22 modprobe: module scsi_wait_scan not found in modules.dep
May  5 13:05:22 modprobe: module mbcache not found in modules.dep
May  5 13:05:22 modprobe: module jbd not found in modules.dep
May  5 13:05:22 modprobe: module ext3 not found in modules.dep
May  5 13:05:22 modprobe: module ext4 not found in modules.dep
May  5 13:05:22 modprobe: module ext2 not found in modules.dep
May  5 13:05:22 kernel: tfat: loading out-of-tree module taints kernel.
May  5 13:05:22 modprobe: module btusbdrv not found in modules.dep
May  5 13:05:22 init: fwver: 3.0.0.4_386_48750-gbc0f14f (sn: /ha:00:90:4C:32:a4:d0 )
May  5 13:05:22 ahs: [read_json]Update ahs JSON file.
May  5 13:05:23 kernel: eth0 (Int switch port: 5) (Logical Port: 5) (phyId: 19) Link Up at 1000 mbps full duplex
May  5 13:05:25 acsd: eth6: selected channel spec: 0xe832 (36/160)
May  5 13:05:25 acsd: eth6: Adjusted channel spec: 0xe832 (36/160)
May  5 13:05:25 acsd: eth6: selected channel spec: 0xe832 (36/160)
May  5 13:05:27 pppd[2176]: Connected to 28:68:d2:00:0f:61 via interface eth0
May  5 13:05:27 pppd[2176]: Connect: ppp0 <--> eth0
May  5 13:05:29 BONDING: option disabled
May  5 13:05:29 roamast: ROAMING Start...
May  5 13:05:30 pppd[2176]: PAP authentication succeeded
May  5 13:05:30 pppd[2176]: peer from calling number 28:68

2:00:0F:61 authorized
May  5 13:05:30 pppd[2176]: local  IP address 10.0.139.223
May  5 13:05:30 pppd[2176]: remote IP address 10.0.138.1
May  5 13:05:30 miniupnpd[2104]: SendNATPMPPublicAddressChangeNotification: cannot get public IP address, stopping
May  5 13:05:30 wan: finish adding multi routes
May  5 13:05:31 miniupnpd[2104]: shutting down MiniUPnPd
May  5 13:05:31 miniupnpd: it is advised to use network interface name instead of 192.168.50.1/255.255.255.0
May  5 13:05:31 miniupnpd[2352]: HTTP listening on port 41733
May  5 13:05:31 kernel: Archer TCP Pure ACK Enabled
May  5 13:05:31 miniupnpd[2352]: Listening for NAT-PMP/PCP traffic on port 5351
May  5 13:05:34 zcip client: configured 169.254.65.54

欢迎光临华硕网络产品技术交流平台 (https://www.52asus.com/)